Home › Media › Page 6

Test-Demonstrations-And-Review-70

Test-Demonstrations-And-Review-70

Annexure: TEST DEMONSTRATIONS AND REVIEW
As part of the IAS accreditation criteria and ISO/IEC 17025 standard, test demonstrations must be observed and reviewed.
Please have the following procedures/records for review:
  • Copy of standards and test procedures
  • Training and qualification records of the staff demonstrating the test
  • Calibration records of the relevant equipment for the corresponding test
Test methods for demonstration:
Test Standard/Method* Title* Comments (if any)
ASTM D3273 Standard test method for resistance to growth of mold on the surface of interior coatings in an environmental chamber
ASTM C241 Standard test method for abrasion resistance of stone subjected to foot traffic
ASTM C609 Standard test method for measurement of light reflectance value and small color differences between pieces of ceramic tile
ASTM C1026 Standard test method for measuring the resistance of ceramic tile to freeze-thaw cycling
CPSC 16 CFR Part 1632 Standard for the flammability of mattresses and mattress pads
California TB 129 Flammability Test Procedure for Mattresses for Use in Public Occupancies
CSFM 12-7A-1 Exterior wall siding and sheathing
UBC 26-3 Room fire test standard for interior of foam plastic systems
UL 1887 Fire test of plastic sprinkler pipe for flame and smoke characteristics
ASTM D543 Standard practices for evaluating the resistance of plastics to chemical reagents
ASTM E759 Standard test method for effect of deflection on sprayed fire-resistive material applied to structural members
ICC-ES AC29 Cold, liquid-applied, below-grade, exterior dampproofing and waterproofing materials
ASME A112.1.3 Air gap fittings for use with plumbing fixtures, appliances, and appurtenances
ASSE 1010 Waterhammer arresters
ASTM F446 Standard consumer safety specification for grab bars and accessories installed in the bathing area
CSA B64.2.1 Hose connection vacuum breakers (HCVB) with manual draining feature
EPA WaterSense Shower heads
IAPMO PS 59 Wastewater diverter valves and diversion systems
ASSE 1061 Performance requirements for push-fit fittings
MaP Toilet Testing Maximum performance (MaP) testing toilet fixture performance testing protocol
Test methods for equipment review:
Test Standard/Method* Title* Comments (if any)
ASTM C518 Standard test method for steady state thermal transmission properties by means of the heat flow meter apparatus
Note:
  • Where test methods require samples to be conditioned for certain duration, test samples should be prepared prior to the assessment. Demonstration of the laboratory’s ability to condition samples to specified parameters will be required.
  • Test demonstrations may be accomplished by using test specimens specifically prepared by the laboratory for this purpose, or the demonstration tests may be actual tests conducted for a client. If the demonstration tests are actual tests for clients, please complete the conditioning of the samples or sample preparation, as needed, prior to our review.
  • All testing witnessed by the IAS assessors will be held in strict confidence.
  • A sampling of project files will be reviewed for all tests that are to be demonstrated. Please have these available for review by the assessors.

Re-assessment-Agenda-70

Re-assessment-Agenda-70

Dear Karthik Easwar,
As agreed, International Accreditation Service (IAS) will be conducting the assessment of your organization.
Purpose of IAS Assessment
To determine the compliance of the organization’s technical and quality systems with the requirements in the following standards, criteria, policies and procedures:

AC89

Assessment Schedule

02-22-2021

02-24-2021

08:00 AM

04:00 PM

5110 N. Mingo Road

Tulsa

OK

74117

United States of America

  • Douglas Sickles(Lead Assessor)
  • J. Musselwhite
  • John Sena


ISO/IEC 17025


S.No Main Checklist Name Assigned to Assessors
1 Main Checklist – TL Douglas Sickles (Lead Assessor)
S.No Checklist Name Assigned to Assessors
1 Supplementary Checklist – TL TAW_1 Douglas Sickles (Lead Assessor)
2 Supplementary Checklist – TL TAW_2 J. Musselwhite
3 Supplementary Checklist – TL TAW_3 J. Musselwhite
4 Supplementary Checklist – TL TAW_4 J. Musselwhite
5 Supplementary Checklist – TL TAW_9 John Sena
6 Supplementary Checklist – TL TAW_10 John Sena

Schedule
The proposed agenda is noted below. The agenda is subject to change depending on the progress of the assessment:
  • Opening Meeting: Introductions, purpose of the assessment, review of the scope of accreditation, adjustments to agenda (if necessary);
  • General Tour of the Organization: Accommodations, flow of work through the facility;
  • Documentation and technical review: Review of documentation and records demonstrating compliance to the applicable standard and accreditation criteria.
  • Field Assessment: Any required field assessments
  • Closing meeting: Presentation of assessment report

Please contact IAS at (562) 364-8201 if you have any questions.
Best Regards,

Lead Assessor

Product-Certification-Agenda-74

Product-Certification-Agenda-74

Annexure: Product Certification Agenda
As part of the IAS accreditation criteria and ISO/IEC 17065, the following scope items will be reviewed as part of the on-site assessment. Also, the following field inspections will be witnessed during the assessment.
Scope:
Major Category* Subcategories*
Building and Construction Seismic
Building and Construction Wind
Building and Construction Physical
Building and Construction Seismic
Witness Inspection Activities:
Scope Category* Product* Date of Inspection*
Building and Construction Certified Wind Product 03-30-2021

Re-assessment-Agenda-74

Re-assessment-Agenda-74

Dear Andrew Coughlin/Anna Lozano/Doug De Risi,
As agreed, International Accreditation Service (IAS) will be conducting the assessment of your organization.
Purpose of IAS Assessment
To determine the compliance of the organization’s technical and quality systems with the requirements in the following standards, criteria, policies and procedures:

AC370

Assessment Schedule

03-30-2021

04-02-2021

08:30 AM

04:30 PM

233 SW Wilson Ave Suite 101

Bend

OR

97702

United States of America

  • David Nelson(Lead Assessor)


ISO/IEC 17065


S.No Main Checklist Name Assigned to Assessors
1 Main Checklist – PCA David Nelson (Lead Assessor)
S.No Checklist Name Assigned to Assessors
1 Supplementary Checklist – PCA Technical Worksheet_1 David Nelson (Lead Assessor)
2 Supplementary Checklist – PCA Technical Worksheet_2 David Nelson (Lead Assessor)
3 Supplementary Checklist – PCA Technical Worksheet_3 David Nelson (Lead Assessor)
4 Supplementary Checklist – PCA Technical Worksheet_4 David Nelson (Lead Assessor)

03-30-2021

03-30-2021

08:30 AM

12:30 PM

TBD

TBD

OR

TBD

United States of America

  • David Nelson(Lead Assessor)


ISO/IEC 17065


S.No Main Checklist Name Assigned to Assessors
No data available in table
S.No Checklist Name Assigned to Assessors
1 Supplementary Checklist – PCA Witness_1 David Nelson (Lead Assessor)

Schedule
The proposed agenda is noted below. The agenda is subject to change depending on the progress of the assessment:
  • Opening Meeting: Introductions, purpose of the assessment, review of the scope of accreditation, adjustments to agenda (if necessary);
  • General Tour of the Organization: Accommodations, flow of work through the facility;
  • Documentation and technical review: Review of documentation and records demonstrating compliance to the applicable standard and accreditation criteria.
  • Field Assessment: Any required field assessments
  • Closing meeting: Presentation of assessment report

Please contact IAS at (562) 364-8201 if you have any questions.
Best Regards,

Lead Assessor

Test-Demonstrations-And-Review-70

Test-Demonstrations-And-Review-70

Annexure: TEST DEMONSTRATIONS AND REVIEW
As part of the IAS accreditation criteria and ISO/IEC 17025 standard, test demonstrations must be observed and reviewed.
Please have the following procedures/records for review:
  • Copy of standards and test procedures
  • Training and qualification records of the staff demonstrating the test
  • Calibration records of the relevant equipment for the corresponding test
Test methods for demonstration:
Test Standard/Method* Title* Comments (if any)
ASTM D3273 Standard test method for resistance to growth of mold on the surface of interior coatings in an environmental chamber
ASTM C241 Standard test method for abrasion resistance of stone subjected to foot traffic
ASTM C609 Standard test method for measurement of light reflectance value and small color differences between pieces of ceramic tile
ASTM C1026 Standard test method for measuring the resistance of ceramic tile to freeze-thaw cycling
CPSC 16 CFR Part 1632 Standard for the flammability of mattresses and mattress pads
California TB 129 Flammability Test Procedure for Mattresses for Use in Public Occupancies
CSFM 12-7A-1 Exterior wall siding and sheathing
UBC 26-3 Room fire test standard for interior of foam plastic systems
UL 1887 Fire test of plastic sprinkler pipe for flame and smoke characteristics
ASTM D543 Standard practices for evaluating the resistance of plastics to chemical reagents
ASTM E759 Standard test method for effect of deflection on sprayed fire-resistive material applied to structural members
ICC-ES AC29 Cold, liquid-applied, below-grade, exterior dampproofing and waterproofing materials
ASME A112.1.3 Air gap fittings for use with plumbing fixtures, appliances, and appurtenances
ASSE 1010 Waterhammer arresters
ASTM F446 Standard consumer safety specification for grab bars and accessories installed in the bathing area
CSA B64.2.1 Hose connection vacuum breakers (HCVB) with manual draining feature
EPA WaterSense Shower heads
IAPMO PS 59 Wastewater diverter valves and diversion systems
ASSE 1061 Performance requirements for push-fit fittings
MaP Toilet Testing Maximum performance (MaP) testing toilet fixture performance testing protocol
Test methods for equipment review:
Test Standard/Method* Title* Comments (if any)
ASTM C518 Standard test method for steady state thermal transmission properties by means of the heat flow meter apparatus
Note:
  • Where test methods require samples to be conditioned for certain duration, test samples should be prepared prior to the assessment. Demonstration of the laboratory’s ability to condition samples to specified parameters will be required.
  • Test demonstrations may be accomplished by using test specimens specifically prepared by the laboratory for this purpose, or the demonstration tests may be actual tests conducted for a client. If the demonstration tests are actual tests for clients, please complete the conditioning of the samples or sample preparation, as needed, prior to our review.
  • All testing witnessed by the IAS assessors will be held in strict confidence.
  • A sampling of project files will be reviewed for all tests that are to be demonstrated. Please have these available for review by the assessors.

Re-assessment-Agenda-70

Re-assessment-Agenda-70

Dear Karthik Easwar,
As agreed, International Accreditation Service (IAS) will be conducting the assessment of your organization.
Purpose of IAS Assessment
To determine the compliance of the organization’s technical and quality systems with the requirements in the following standards, criteria, policies and procedures:

AC89

Assessment Schedule

02-22-2021

02-24-2021

08:00 AM

04:00 PM

5110 N. Mingo Road

Tulsa

OK

74117

United States of America

  • Douglas Sickles(Lead Assessor)
  • J. Musselwhite
  • John Sena


ISO/IEC 17025


S.No Main Checklist Name Assigned to Assessors
1 Main Checklist – TL Douglas Sickles (Lead Assessor)
S.No Checklist Name Assigned to Assessors
1 Supplementary Checklist – TL TAW_1 John Sena
2 Supplementary Checklist – TL TAW_2 J. Musselwhite

Schedule
The proposed agenda is noted below. The agenda is subject to change depending on the progress of the assessment:
  • Opening Meeting: Introductions, purpose of the assessment, review of the scope of accreditation, adjustments to agenda (if necessary);
  • General Tour of the Organization: Accommodations, flow of work through the facility;
  • Documentation and technical review: Review of documentation and records demonstrating compliance to the applicable standard and accreditation criteria.
  • Field Assessment: Any required field assessments
  • Closing meeting: Presentation of assessment report

Please contact IAS at (562) 364-8201 if you have any questions.
Best Regards,

Lead Assessor

Work-Force-Qualification-Agenda-73

Work-Force-Qualification-Agenda-73

Annexure: Work Force Qualification Agenda
As part of the IAS accreditation criteria for Training Agencies for Work Force Qualification Programs the following information will be reviewed as part of the on-site assessment.
Technical Requirements
  • Observation of instruction
  • Organizational structure (technical staffing and oversight)
  • Needs analysis
  • Program planning
  • Public (client) information
  • Training and delivery
  • Evaluation
  • Renewals
  • Confidentiality
  • Security
  • Test methods and method validation
Records to Be Reviewed (please have these readily accessible):
  • Legal-registration documents of the agency
  • Quality manual for curriculum development and for training programs
  • Reports on “quality metrics”
  • Reports on “Benchmarking” goals, research procedures, and reports
  • Customer satisfaction survey reports and records on actions taken (if any)
  • Internal audit records, including management review and actions taken (if any)
  • Technical records in support of program goals specified in the quality manual.

Initial-Assessment-Agenda-73

Initial-Assessment-Agenda-73

Dear Patrick Test/Ztest Testing,
As agreed, International Accreditation Service (IAS) will be conducting the assessment of your organization.
Purpose of IAS Assessment
To determine the compliance of the organization’s technical and quality systems with the requirements in the following standards, criteria, policies and procedures:

AC371

Assessment Schedule

02-10-2021

02-10-2021

09:45 AM

01:15 PM

1234 Testing

Whittier

NA

45782

Bailiwick of Jersey

  • Patrick McCullen(Lead Assessor)

No standard available
S.No Main Checklist Name Assigned to Assessors
No data available in table
S.No Checklist Name Assigned to Assessors
1 Main Checklist – QPT_1 Patrick McCullen (Lead Assessor)
2 Technical Worksheet_1 Patrick McCullen (Lead Assessor)

Schedule
The proposed agenda is noted below. The agenda is subject to change depending on the progress of the assessment:
  • Opening Meeting: Introductions, purpose of the assessment, review of the scope of accreditation, adjustments to agenda (if necessary);
  • General Tour of the Organization: Accommodations, flow of work through the facility;
  • Documentation and technical review: Review of documentation and records demonstrating compliance to the applicable standard and accreditation criteria.
  • Field Assessment: Any required field assessments
  • Closing meeting: Presentation of assessment report

Please contact IAS at (562) 364-8201 if you have any questions.
Best Regards,

Lead Assessor

Test-Demonstrations-And-Review-72

Test-Demonstrations-And-Review-72

Annexure: TEST DEMONSTRATIONS AND REVIEW
As part of the IAS accreditation criteria and ISO/IEC 17025 standard, test demonstrations must be observed and reviewed.
Please have the following procedures/records for review:
  • Copy of standards and test procedures
  • Training and qualification records of the staff demonstrating the test
  • Calibration records of the relevant equipment for the corresponding test
Test methods for demonstration:
Test Standard/Method* Title* Comments (if any)
ABC sdfasfdsad
asdfs adsfasdf
asdfsadf asfdsaf
Test methods for equipment review:
Test Standard/Method* Title* Comments (if any)
ASDASD ASDASD
Note:
  • Where test methods require samples to be conditioned for certain duration, test samples should be prepared prior to the assessment. Demonstration of the laboratory’s ability to condition samples to specified parameters will be required.
  • Test demonstrations may be accomplished by using test specimens specifically prepared by the laboratory for this purpose, or the demonstration tests may be actual tests conducted for a client. If the demonstration tests are actual tests for clients, please complete the conditioning of the samples or sample preparation, as needed, prior to our review.
  • All testing witnessed by the IAS assessors will be held in strict confidence.
  • A sampling of project files will be reviewed for all tests that are to be demonstrated. Please have these available for review by the assessors.

Re-assessment-Agenda-72

Re-assessment-Agenda-72

Dear Patrick Test/Server April Testing,
As agreed, International Accreditation Service (IAS) will be conducting the assessment of your organization.
Purpose of IAS Assessment
To determine the compliance of the organization’s technical and quality systems with the requirements in the following standards, criteria, policies and procedures:

AC89

Assessment Schedule

02-10-2021

02-10-2021

08:30 AM

03:30 PM

1 Birch

Brea

CA

92821

United States of America

  • Helga Alexander(Lead Assessor)
  • Igor Erenburg


ISO/IEC 17025


S.No Main Checklist Name Assigned to Assessors
1 Main Checklist – TL Helga Alexander (Lead Assessor)
S.No Checklist Name Assigned to Assessors
1 Supplementary Checklist – TL TAW_1 Igor Erenburg
2 Supplementary Checklist – TL TAW_2 Helga Alexander (Lead Assessor)

Schedule
The proposed agenda is noted below. The agenda is subject to change depending on the progress of the assessment:
  • Opening Meeting: Introductions, purpose of the assessment, review of the scope of accreditation, adjustments to agenda (if necessary);
  • General Tour of the Organization: Accommodations, flow of work through the facility;
  • Documentation and technical review: Review of documentation and records demonstrating compliance to the applicable standard and accreditation criteria.
  • Field Assessment: Any required field assessments
  • Closing meeting: Presentation of assessment report

Please contact IAS at (562) 364-8201 if you have any questions.
Best Regards,

Lead Assessor